KatanzaroProfessional production of cargo elevatorsThings to pay attention to during production / vlog_20145_WOkHVR

category：Building materials / date：2024-04-08 00:12:47 / browse：43 / comment：6

The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply,Katanzaro1 ton lifting cargo elevator, single-phase or three-phase power supply, and diesel engine.KatanzaroThe ripper does not move up or down or the lifting force is weak: the pressure adjustment of the relief valve does not meet the requirements and adjust the pressure to the required value; see the cleaning in item above for the internal leakage of the oil cylinder; the reversing valve is locked or internal leakage; The oil tank is blocked; the oil supply pump is faulty; the one-way valve checks the wear and damage of the one-way valve core and valve seat, and whether the one-way valve spring is fatigued or deformed.Hydraulic pump station: special pump station for domestic lifting platform,KatanzaroGuide rail lifting cargo elevator, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Hamburg-Eimsbuettel,After the goods are transported, clean up the debris on the platform.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.

Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?There are foreign objects inside the oil delivery pipe of the hydraulic lifting platform which causes uneven force on the hydraulic oil delivery, and uneven table tops. It is recommended to carefully check whether the oil delivery pipe is unblocked.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Packaging strategySystem: explosion-proof electronic control system, remote control system, P IC system.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.

Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Good reputation,The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Looseness occurs: The newly processed and assembled parts of mobile lifts and other aerial work platform equipment have a tendency to geometric shape and matching size. , Coupled with excessive wear and other reasons, it is easy to loosen the originally fastened parts of aerial work platform equipment such as mobile lifts.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Katanzaro, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits,KatanzaroHeavy industry guide rail type cargo elevator, reducing engineering construction costs and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.