Bog Walk Cement waterproof boardWhat are the markets for investment / viewnews7421

category：Environmental protection / date：2023-06-05 20:06:59 / browse：160 / comment：6

Super wear-resistant. The wear-resistant layer on the surface of SPC floor is a transparent wear-resistant layer processed by high technology, the service life of SPC floor is more than - years.SPC floor is a long-life floor, especially suitable for public places with large flow of people and high degree of wear.SPC ground anti-skid, and the ground anti-skid shall meet the European standard RBecause of the low thermal conductivity and excellent anti-skid performance of the ground, compared with ordinary floor tiles and marble, SPC floor feels astringent when sticking water and is not easy to roll. Therefore, ground building decoration materials are preferred in public places with high safety regulations, showers, hospitals, kindergartens, medical management centers, rehabilitation hospitals, colleges and universities, which are very popular in China in recent years.Bog Walk , Brush the finish paint three to four times according to the above procedure,Bog Walk What color does floor leather look good, and the last time does not need polishing.The wide board specification was invented by China&#;s laminate flooring processing enterprises in order to meet consumer demand. Its advantages look generous, and there are relatively few gaps in the floor. Most of them are thickened, that is, the decorative paper on the surface is made in China, with many changes in design and color, which is more flexible. The disadvantage is that the color difference is relatively large, and the anti ultraviolet ability of the decorative paper is poor.AnehoThe general specification and model of general floor is cm×cm, the specification and model of high-capacity floor can reach cm×cm, with a total area of times that of the general wooden floor.The floor is generally made of common materials such as red sandalwood and Huanghua pear wood. The corner material is discarded and made of a key part of the whole tree. It mainly shows the air. The road construction has an endless sense of flexion and extension and three-dimensional feeling.Third, it is flame retardant, but it can&#;t be burned.The surface of SPC floor has a special transparent wear-resistant layer processed by high technology, and its wear-resistant revolution can reach more than revolutions.Among the traditional ground materials, the wear-resistant laminate floor has only - revolutions.The name SPC floor is easy to cause people&#;s misunderstanding. SPC floor is one of the categories of PVC floor. When you think of PVC floor, you think more of plastic. Many people will confuse PVC floor with PVC pipe. Plastic contains toxic substances and is harmful to human body.

Common types: three-layer solid wood composite floor, double-layer solid wood composite floor, new solid wood composite board.It is simple to clean, bright as new, with good wear resistance, and does not need to spend a lot of energy on maintenance. It is reported that good solid wood composite floor in the market can keep the paint bright as new without waxing within years. This is in sharp contrast to the shape and maintenance of wood floor.Floor leather (also known as coiled floor), a new type of flooring material,Bog Walk Waterproof and tile adhesive,Bog Walk Waterproof wood floor, glass wire with good flatness or double primer is used.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.Advantages of floor leatherEncyclopedic knowledge,When assembling the solid wood floor, do not be too loose or too tight.The assembly relaxation shall be reasonably arranged according to the temperature of the indoor environment. The assembly relaxation will produce a large gap with the shrinkage of the floor.The assembly is too tight and the floor is arched when it expands. SmellOne of the modern trends in house design is WPC wood flooring.Because of their many qualities, many people like this floor better than others.However, if you will find the quality and durability of SPC flooring, you will also leave people that WPC and SPC flooring have their advantages and disadvantages.If you choose one of them, it&#;s no problem!Now we&#;ll tell you the difference between the two.

The flame retardant grade is B, and the formaldehyde concentration is acceptable.Precautions for solid wood floor installation : prevent uneven ground.middleman,Precautions for solid wood floor installation : do not use the fixing method of wooden wedge and nail.Finally, look at the price.The first kind: pungent taste. If the floor tastes like this, it means that it contains a lot of formaldehyde. You need to be careful when choosing. You&#;d better not buy it;Bog Walk , Easy to clean: medical treatment is simple, bright as a new mouth, no stains, easy to clean.The surface paint of solid wood composite floor is very good, with good wear resistance, without excessive vitality maintenance.According to statistics, the solid wood composite floor prepared for the sales market will not be waxed within years, and the wind color of automobile coating will also be maintained.This is obviously compared with the maintenance of solid wood flooring.The real wood floor is processed with a whole plate, with natural texture, and its section texture can correspond to the surface texture one by one;Fake solid wood floor is mostly pasted with leather or stickers on the fake floor, so the cut texture is not commensurate with the surface texture.The standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g g, g, and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach - or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary, the cost is much higher if the number of wear-resistant revolutions is high.