category:Machinery and industry equipment / date:2024-05-11 01:48:39 / browse:54 / comment:6
Assembly of rotor parts of submersible slurry pump Before assembly apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage. The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.Zwitter steft, The sewage pump will leak. If the water pipe leaks, it will reduce the power of the water pump and even damage the sewage pump. In case of fixed installation, it shall be applied on the pipe to avoid leakage. Pages can be welded by electric welding, buried in the soil, coated with asphalt, and then should not be gassed. Steaming of tap water products The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.Caucaia, First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared. In fact,Zwitter steftAh slurry pump, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded In addition, the noise method directly detects the noise of the equipment in the detection process but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.
Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation. Submersible slurry pump Absorb silt and sand from rivers, lakes, oceans, reservoirs, fish ponds and power plants. Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s. The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.Welcome calls , When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed,Zwitter steftSubmersible slurry pump, because it does not need too many auxiliary facilities.
Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.superior quality,Zwitter steftSubmersible non clogging slurry pump, In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too Starting mode. It can be widely used in industrial and agricultural production, water supply, drainage, fire control, sprinkler pipe network pressurization, HVAC cold and hot water circulation and other occasions. To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor will fall into the water the water pipe shall be short and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration. Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.
share 6 Comments
Comment / Cancel reply