category：Building materials / date：2024-04-26 02:51:30 / browse：33 / comment：3
Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, electrical silicon steel sheet, strip steel, square pipe, metal products etc.Bykhaw,High temperature diffusion heat treatment of ingot can improve the composition heterogeneity of ingot and improve the transverse performance of square tube.Functional index analysis of qb square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of qb square tube data under load.San-Mateo-Ixtatan,Engaged in square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However,BykhawHow much is a galvanized pipe, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, square tube steel and non-ferrous metal.
Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.Function index analysis of square tube - the strength acts on the parts in a great progress. The load on the parts is called the charge and trap load. The power of square tube destruction under the charge and trap load is called the charge and trap toughness.Square tube, modified square tube, square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, and then the shaping unit will roll the round pipe into square pipe, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point, excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, due to the different forming bending radians of products with different wall thickness, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.Pursuit of excellence,Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.
Derusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.Welcome calls ,It is the process of drawing the die hole of the rolled metal blank (shape, pipe, product, etc.) into a section to reduce the length and increase. It is mostly used for cold processing.Large fillet radius, insufficient blank holder area, easy to produce unstable wrinkles; If the fillet is too small, the resistance of the material into the die will increase in the deformation process, and the material is not easy to move and transfer inward, thus increasing the large tensile stress in the force transfer area, which may lead to tensile cracking.When storing QB square pipe,BykhawGalvanized square pipe manufacturing, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, dry and ventilated, where harmful gases appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe so try to cut it and don't let it. In addition, we can put them into the warehouse for very good retention. According to geographical conditions if we can think about those higher metal products, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, sulfur s, phosphorus P and chromium CR.Bykhaw,When storing QB square pipe we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, dry and ventilated where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, which can be seamless pipe or welded pipe such as air cylinder or oil cylinder, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection and the density of steel is relatively good. After cold drawing and heating, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.
share 3 Comments
Comment / Cancel reply