category：Machinery and industry equipment / date：2024-04-24 01:09:16 / browse：54 / comment：4
Stability and reliability of seals between pump bodies. After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment andDorn bean, Consider the vertical separation level of the tail equipment. The water pump control cabinet has a variety of protection s and complete status display, such as overload, short circuit, phase loss protection, pump body water leakage, motor over temperature and electric leakage as well as single pump and multi pump control working modes, a variety of main and standby pump switching modes and various When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoidKaiyun, Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time. It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect. The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.
Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand,Dorn beanCorrosive pipeline pump, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,Dorn beanVertical heavy-duty slurry pump, we only need to fix the pump shaft and rotate the impeller in reverse to remove the impeller easily. For large pumps with impeller removal ring, we need to remove the impeller removal ring first, wide flow passage strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.Online consultation, After meters, the sealing of the equipment can not bear the water pressure at this depth. Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage. Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.Quality assurance, Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade power type (special hollow shaft motor,Dorn beanFire deep well pump, ordinary vertical motor, diesel engine or other power) Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustmentDorn bean, Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out? Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.
share 4 Comments
Comment / Cancel reply