category:Machinery and industry equipment / date:2024-04-18 03:27:37 / browse:36 / comment:5
The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.Andorra la Vella , rotate the impeller to check whether it is flexible, and check whether the seals at the pump vent hole, water drain hole, oil drain hole and cable joint are loose. If they are loose, they must be tightened. There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Lets take a look at the difference between the two.Port-of-Spain, Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse. When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out? If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,
repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry. Solution: replace the remote pressure gauge; Replace the pressure transmitter; Check the connecting signal wire. Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them,Andorra la Vella Carbon steel explosion-proof pipeline pump, which will cause equipment problems and affect work efficiency. So were usingRecommendation and consultation,Andorra la Vella Self priming non clogging sewage pump, In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the pump head shall be determined by enlarging the margin of % - %. The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two
After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started,Andorra la Vella Self priming slurry pump wholesale, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.Convenient and efficient, We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself The pump fails to supply water or the flow is insufficient. The pump fails to supply water or the flow is insufficient. It is likely that the suction pipe has water leakage or the bottom valve has air leakage, but there are several possible reasons: the water inlet is blocked; The bottom valve is not deep enough underwater; The running speed of the water pump is not enough; leaf With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data in the second half of the year, The secondary pump shaft seal of the two-stage series pump is (packing seal) there is still a large gap after Chinas power balance.Andorra la Vella , and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated power Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation. The utility and durability of the utility model, so the polymer composite materials are generally used in production.
share 5 Comments
Comment / Cancel reply