category：Building materials / date：2024-05-10 04:57:23 / browse：42 / comment：3
It has the characteristics of high efficiency and low cost. At the same time, we use this method to weld joints and repair joints with a one-time qualified rate of welding), which is worthy of our use.First of all, let's understand what stainless steel is. Generally speaking, steel that will not rust is called stainless steel, but in an academic sense, steel resistant to weak corrosive media such as air, alkali and salt. Also known as stainless acid resistant steel. In practical application, the steel resistant to weak corrosion medium is often called stainless steel, while the steel resistant to chemical medium is called acid resistant steel. Due to the difference in chemical composition between the two, the former is not necessarily resistant to chemical medium corrosion, chromium reacts with oxygen in the corrosive medium to form a thin oxide film (self passivation film) on the steel surface, which can prevent further corrosion of the steel matrix. In addition to chromium, the commonly used alloy elements include nickel, molybdenum, titanium, niobium, copper, nitrogen, etc., so as to meet the requirements of various uses on the microstructure and properties of stainless steel.Tutrakan,SPCC stainless steel belt is simply an extension of ultra-thin stainless steel plate. It is mainly a narrow and long steel plate produced to meet the needs of industrialized production of various metal or mechanical products in different industrial sectors.The back side is not protected by argon, and the flux coated welding wire (self protective flux cored welding wire) + TIG process is adopted. In the s the backing welding wire has been developed. Recently, China has also developed the stainless steel backing welding wire (i.e. flux coated welding wire, such as tgftgftgftgf, etc.) It has been applied to the actual construction and achieved good results. We have successfully applied it in the capacity expansion and reconstruction project of Urumqi Petrochemical.Berrechid,Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.The corrosion resistance of stainless steel depends on chromium,TutrakanStainless steel tape magnetic, the protection is different.Model & mdash; General model; stainless steel. The GB brand is CrNi.
There shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage,Tutrakan303 stainless steel welded pipe, the storage position shall be convenient for lifting and absolutely isolated from other data storage areas. Protective measures shall be taken to avoid purification, collision with other components, purification and damage of iron metal.Air pressure and water pressure test: conduct water pressure test for pressure resistant pipes one by one, and keep it for no less than seconds at the specified pressure value. The water pressure test of conventional supply is MPa. The air pressure test is p = .mpaa.In the building water supply pipe system, due to the end of the glorious history of galvanized steel pipe, various new plastic pipes and composite pipes have developed rapidly, but various pipes still have some deficiencies in varying degrees, which are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. Therefore, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience, stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe.Where can I find it?,The product quality advantages of continuous casting billet of stainless steel pipe fittings are mainly reflected in that the non grinding rate of the outer surface of the billet except the head and tail section has reached more than %, and the total surface grinding yield has reached %. In order to achieve this goal, it is necessary to refine the molten steel, achieve low oxygen and sulfur content, do a good job in the metallurgy of the ladle and tundish, accurately determine the molten steel temperature and realize no oxidation casting, Further reduce the inclusion content.Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.Stainless steel grade group Series & mdash; Chromium nickel manganese austenitic stainless steel series & mdash; Chromium nickel austenitic stainless steel model & mdash; Good ductility used for molding products. It can also be machined to harden rapidly. Good weldability. The wear resistance and fatigue strength are better than those of stainless steel.
Stainless steel has been used as a structural material for building new buildings and repairing historic sites for more than years. Early designs were calculated according to basic principles. Today, design codes, such as ANSI as of the American Society of civil engineers, are usedproject,When hoisting stainless steel pipes, public slings,TutrakanStainless steel water pipe 304, such as hoisting belt and public collet number, shall be used. It is strictly prohibited to use steel wire rope to avoid scratching the surface; and when hoisting and placing, it shall prevent scratching caused by impact and collision. If there are surface scratches, electric arc traces and surface purification in the process of transportation, storage and processing, it must be completely cleaned, polished with an angle grinder, and then polished Polishing with optical sheet or metallographic sandpaper.Cold drawn (rolled) seamless steel pipe: round billet → Heating → Perforation & rarr; Lead & rarr; Annealing & rarr; Pickling → Oiling (copper plating) → Multi pass cold drawing (cold rolling) → Blank tube & rarr; Heat treatment & rarr; Straightening & rarr; Hydrostatic test (flaw detection) → Mark & rarr; Warehousing.Austenitic stainless steel. It contains more than % chromium, about % nickel and a small amount of molybdenum, titanium, nitrogen and other elements. Good comprehensive performance and resistance to corrosion of various media.Tutrakan,Standard classification - classification: national standard GB industry standard Yb local standard enterprise standard qcb- classification: product standard packaging standard basic standard - standard level (divided into three levels): y level: international advanced level I level: international general level H level: domestic advanced level - national standard: stainless steel bar (level I) gb- stainless welding disc Park (level H)Typical ferritic stainless steels are Crl, Cr and Cr.When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.
share 3 Comments
Comment / Cancel reply