category：Building materials / date：2024-04-16 06:07:13 / browse：53 / comment：6
There are three main reasons for oxidation of stainless steel: production process, which is one of the reasons for oxidation of steel products. In terms of production process and product characteristics, forming a thin oxide film on the product surface is the basic process to avoid oxidation, and it is also one of the main characteristics of steel products different from other steel products. It is specialized in products, renewable resources business and business package Including: stainless steel plate, stainless steel coil, stainless steel belt and stainless steel pipe. However, when the oxide film is incomplete and discontinuous due to insufficient or negligent production process, the oxygen in the air will directly react with some elements in the product,Stijena202 stainless steel plate, resulting in the appearance of oxidation of the product.For business people, of course, it is better to spend less under feasible conditions. For goods such as stainless steel pipes, we can often see that there will be packaging film bags on them. Although they are not heavy, if there are a large number of single purchases,StijenaPickling of stainless steel pipe, they will also produce certain economic expenses, but why do many people clearly dislike this thing on stainless steel pipes, But I have to accept it. Next, xincoral Xiaobian will tell you why stainless steel pipes need packaging bags.StijenaCold rolled non oriented silicon steel strip consists of nominal thickness (expanded by times) + code a + iron loss guarantee value (the value after expanding the iron loss value when the frequency is Hz and the large magnetic flux density is T by times). For example, a indicates that the thickness is .mm and the guaranteed value of iron loss is & le; cold rolled non oriented silicon steel strip.Stainless steel pipes and water transmission equipment for fluid transportation such as water and gas are advanced basic water purification materials in the world. They have strong anti-corrosion performance, which can not be compared with cast iron pipes, carbon steel pipes and plastic pipes.Nyaungdon,Inspection: after crimping, check the crimping size with a special gauge.According to the purpose, it can be divided into oil well pipe (casing, oil pipe and drill pipe), pipeline pipe, boiler pipe, mechanical structure pipe, hydraulic prop pipe, gas cylinder pipe, geological pipe, chemical pipe (high-pressure chemical fertilizer pipe, petroleum cracking pipe) and marine pipe.Martensitic stainless steels typical martensitic stainless steels include Cr ~ Cr and Cr, which have good processing properties. Deep drawing, bending, crimping and welding can be carried out without preheating. Crl does not require preheating before cold deformation, but preheating is required before welding. crlcr is mainly used to make corrosion-resistant structural parts such as steam turbine blades, while crcr is mainly used to make surgical and wear-resistant parts of medical instruments; crl can be used as corrosion-resistant bearings and tools.
Stainless steel pipe, which was produced and used in China at the end of the s, stainless steel belt and stainless steel pipe for a long time. The designated products are complete and the quality is guaranteed. For example, a means that the thickness is .mm and the iron loss guarantee value is ≤ cold rolled non oriented silicon steel strip.Adjust the ratio of austenite forming elements to ferrite forming elements in the steel to make it have austenite + ferrite dual phase structure, in which ferrite accounts for % - %. This dual phase structure is not easy to produce intergranular corrosion.Direct labor Series & mdash; Martensitic precipitation hardening stainless steel.When hoisting stainless steel pipes, public slings, such as hoisting belt and public collet number, shall be used. It is strictly prohibited to use steel wire rope to avoid scratching the surface; and when hoisting and placing, it shall prevent scratching caused by impact and collision. If there are surface scratches, electric arc traces and surface purification in the process of transportation, storage and processing, polished with an angle grinder, and then polished Polishing with optical sheet or metallographic sandpaper.The scale pretreatment of stainless steel pipe makes the scale loose, and then acid pickling is carried out for easy removal. The pretreatment can be divided into the following: alkaline salt melting treatment method. The alkaline melt contains % hydroxide and % salt. The proportion of the two in the molten salt shall be strict, so that the molten salt has strong oxidizing power, low melting point and small viscosity. Only the sodium halo shall be analyzed in the production process, and the content shall not be less than % (wt) It is treated in a salt bath furnace at ~ ℃ for minutes for ferritic stainless steel and minutes for austenitic stainless steel. Similarly, iron oxides and spinels can also be oxidized by salt to become loose ferric oxide, some of the formed oxides peel off and sink to the furnace bottom in the form of sediment. Alkaline salt melting pretreatment Process flow: steam degreasing → preheating ( ~ ℃, time ~ min) ↠ molten salt treatment & rarr; water quenching & rarr; hot water washing. Molten salt treatment is not suitable for assemblies with weld gap or crimping. When the parts are taken out of the molten salt furnace, a stream of alkali and salt mist will be splashed during water quenching, so deep well anti splash water quenching tank shall be used during water quenching. During water quenching, firstly lift the parts basket into the tank, stop above the horizontal plane, close the tank cover, and then lower the parts basket into the water Professional L stainless steel pipe, s stainless steel pipe and L stainless steel pipe are stable, safe, reliable and maintenance free. The technical level has reached the domestic level and the international advanced level of similar products until submerged.
Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, other properties are similar. Stainless steel decorative pipe, stainless steel pipe, series stainless steel pipe & mdash; Ferritic and martensitic stainless steel model & mdash; Good heat resistance, weak corrosion resistance, % Cr, % Ni.Recommendation and consultation,Stainless steel pipe can be divided into equal section pipe and variable section pipe according to the profile shape. Variable section pipes include conical pipes, stepped pipes and periodic section pipes.Stainless steel pipe is a common material in stainless steel, with a density of GCM, which is also called stainless steel in the industry. High temperature resistance of ℃, with the characteristics of good processing performance and high toughness, furniture decoration industry and food and medical industry.Application: utility boiler industry, mainly in key parts such as high temperature section of superheater and reheater.Stijena,Clamping connection steps: cut off the pipe according to the required length. When breaking the pipe, it shall not be too large to prevent the pipe from being out of round.When the addition of chromium reaches %,StijenaStainless steel chain plate mesh belt, the atmospheric corrosion resistance of steel increases significantly, but when the chromium content is higher, although the corrosion resistance can still be improved, it is not obvious. The reason is that when alloying steel with chromium, the type of surface oxide is changed to be similar to that formed on pure chromium metal. This tightly adhered chromium rich oxide protects the surface from further oxidation. This oxide layer is very thin. Through it, you can see the natural luster of the steel surface which makes the stainless steel have a unique surface. Moreover, the steel surface will react with the atmosphere to repair itself if the surface layer is damaged, re form this passive film and continue its protective effect.Welding of stainless steel pipe argon arc welding stainless steel pipe: it is required to have deep penetration, no oxide inclusion, and the heat affected zone can be as small as possible. Argon arc welding maintained by tungsten inert gas has good compliance, nuclear and food industries.
share 6 Comments
Comment / Cancel reply