WolfsburgIrrigation deep well pumpHow to maintain it / article21868

category：Machinery and industry equipment / date：2024-05-02 01:46:54 / browse：46 / comment：4

then inject water into the pump body,WolfsburgCarbon steel explosion-proof pipeline pump, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found,WolfsburgVertical centrifugal slurry pump, apply lubricating oil or mixed paint on the joint after disassembly and tighten the screws.　　Superior, complete protection s, reasonable structure, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.Wolfsburg,　　As a display screen, the operation of each fire pump is clear at a glance, and the management is very convenient.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, soPirae,　　What is the cause of pump overload.　　Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　It is an auxiliary means for some on-site monitoring.

　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　 water　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.Work courses,　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　In this way, replace it with a new one.

　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energyHome page recommendation,　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　I believe you have such a question when using the submersible sewage pump, is this pump a submersible pump? Or is it a sewage pump? In fact, this question is very easy to distinguish. You can take a look at the following contents sorted out by Shanghai Shenquan.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.Wolfsburg,　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,　　However,WolfsburgUsed pipeline pump, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, metallurgy and coal　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating