Talus6-point galvanized square pipeProblems encountered and Solutions / article19482

category：Building materials / date：2024-03-29 02:41:05 / browse：36 / comment：3

Hot dip galvanized square pipe is widely used, mainly in curtain wall, solar power generation support, construction,TalusHow much is 30 galvanized square tube, machinery and steel structure engineering, especially in curtain wall machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.Talus,During the storage of square tubes, pay attention to the stacking layers of square tubes to avoid local stress at the tube end caused by too many layers, resulting in radial plastic deformation and layer damage of square tubes. It is recommended that the stacking layers of smooth pipes refer to apirp l- Recommended Practice for railway transportation of square pipes for pipelines or apirp lw- Recommended Practice for ship and sea vessel transportation of square pipes for pipelines. It can also be determined by test or implemented according to the safe stacking height of square pipes. The stacking layers of pipes shall be implemented according to GBT - polyethylene layer of buried steel pipelines.If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed),Talus25 price of galvanized square pipe, the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), and propose acceptance with a new batch.Radovish,Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral welding

The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.However, there is a large rate of end in the application of steel pipe, which is mainly due to the trouble of internal and external treatment. The primary external question is very crucial, and its external quality directly affects its applicationThere are many ways of ignition such as arc, electric spark, flame, strong current, high-temperature furnace, electron beam laser, high-temperature radiation, microwave, chemical furnace,Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food, machinery and other industries.During the pushing process of spot welding and repair welding elbows, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, there are about wires thinned. If the technology is not good or the drawn pipe is used, the thickness is significantly lower than the standard.The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, the adobe has cracks due to the action of thermal stress and there are cracks after rolling.

Solution treatment and nondestructive testing sand rolling treatment and sand blasting treatment many manufacturers in the market do not do solution treatment and % penetration nondestructive testing, and many of them use sand blasting instead of sand rolling. After these steps are omitted, the cost is greatly reduced.knowledge,Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.The square tube adopts the electric contact pressure gauge to press down the pressure of the oil cylinder on both sides of the conveyor to ensure the smooth transportation of the strip steel.Forging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.Talus,Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking, shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, plates and tubes. It is divided into cold rolling and hot rolling.