Brooke in the wildernessSubmersible pump can pump sewageSpot inventory resources / 49baec_466HP159575805_22385

category：Machinery and industry equipment / date：2024-05-10 05:35:40 / browse：53 / comment：6

　　During the process, but in fact the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, we use it at ordinary times　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterBrooke in the wilderness,　　Stainless steel deep well pump can dive underground and pump hot water from deep underground. However, due to a large amount of humus and water vapor underground, it is easy to adhere to the surface of various instruments and tools, resulting in rust and shortened service life. Is the stainless steel deep well pump easy to break? Use for a period of time　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.Puerto-Cortes,　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media,Brooke in the wildernessVertical slurry pump, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　So it is called: submersible slurry pump.　　 First remove the pump from the engine.

　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　 Service conditions　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.Service first　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　Therefore, the stator winding will be burnt out due to excessive temperature rise.

　　For example, in the market, for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition,　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　Or nodular cast iron, vertically split, bolted. The pump body is connected with the bracket with bolts. The discharge outlet of the pump can be rotated and installed at intervals of ℃ and eight angles as required.　　Whether the pump is evacuated or overflowed,Brooke in the wildernessRubber lining submerged slurry pump, etc., and handle it at any time.Brooke in the wilderness,　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.