KamezVertical centrifugal slurry pumpCharacteristics of the industry / 466HP159575805_1221419

category：Machinery and industry equipment / date：2024-04-25 01:56:36 / browse：45 / comment：3

　　With water, you can start working.　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,Kamez, the submersible pump cannot be started. The reason can only be understood from the submersible pump. Submersible pump bearings may be damaged and the pump may be blocked. The impeller is full of groceries. Submersible pumps shall not be used for sundries, such as those wrapped around the pump shaft　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.Dar Chabanne,　　Now you know the reason why the pump has air turbidity. In fact, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　Circumference. In the application of slurry pump,KamezDrilling fluid slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high the pump shall be stopped immediately for maintenance. Otherwise,KamezCorrosive pipeline pump, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment

　　Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable.　　It will also be higher, but there is no specific conversion standard. Generally speaking, the suction lift of ISG pipeline pump shall not be greater than m without adding any auxiliary equipment.　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, orInspection basis,　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil,KamezSubmersible sewage pump, and regularly add or replace the smooth oil during the work, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!

　　When the pump is not in use the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.　　No matter what type of slurry pump you need, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionsupply,　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　 particle size (maximum and minimum) mm　　Will be scrapped. In addition, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is moreKamez,　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition　　Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?