KennethHousehold outdoor elevator on the third floorThe role of anticorrosive phosphating treatment / 35-12-21872

category：Machinery and industry equipment / date：2024-05-02 02:01:34 / browse：49 / comment：3

Restore the command button function in the cabin for firefighters to operate.If the elevator is in a downward direction,KennethFully electric high-altitude reclaimer, immediately close the door and return to the first floor station,KennethHydraulic barrier free elevator, and automatically open the elevator door.Kenneth,As elevator people, let's talk about elevator and elevator safety knowledge: The elevators we currently use include box type passenger elevators escalators, and dedicated cargo elevators. Dedicated cargo elevators are installed due to special needs, and we don't use many of them. Now, let's take a look at the safety knowledge of box type passenger elevators and escalators: When we take escalators, Be sure to follow the safety instructions when riding on the elevator. Do not crowd or play around, hold onto the elevator firmly, fasten your shoelaces, and avoid getting them caught up.The effective support width of the upper and lower support beams should be greater than the width of the escalator truss, and there should be embedded steel plates.Argos,The effective support width of the upper and lower support beams should be greater than the width of the escalator truss, and there should be embedded steel plates.Multiple elevator shafts can be connected and an - # I-beam can be fixed at a certain height between each adjacent elevator shaft, when instructed by the fire center or the dedicated operation button of the first floor firefighter to enter the firefighting state, the elevator should immediately stop on the floor without opening the door, return to the first floor station, and automatically open the elevator door if it is in the upward direction.

In the event of a fire, when instructed by the fire center or the dedicated operation button of the first floor firefighter to enter the firefighting state, the elevator should immediately stop on the floor without opening the door, return to the first floor station, and automatically open the elevator door if it is in the upward direction.The seat elevator person sits on a chair driven by an electric motor, and the button on the chair handle causes the power drive device at the bottom of the chair to drive the person chair up and down along the guide rail of the staircase railingMeasurement of elevator shafts in new construction projects under different on-site conditions: When the building design is not yet completed, the operator only needs to provide the user with the standard elevator layout of the required elevator specifications, and the user entrusts the design department to design the elevator shaft. When the architectural design has been completed, and the site has not yet been constructed, is under construction, or has been completed, it must be determined based on the current construction or measured dimensions. If the original civil design of the shaft needs to be modified, the user should entrust the architectural design department to make the shaft design modification based on the layout provided by the elevator.Focus on Development,In the event of a fire, when instructed by the fire center or the dedicated operation button of the first floor firefighter to enter the firefighting state, the elevator should immediately stop on the floor without opening the door,KennethFamily villas and elevators, return to the first floor station, and automatically open the elevator door if it is in the upward direction.The front room of the fire elevator is equipped with Class B fireproof doors or fireproof rolling shutters with stopping function.Multiple elevator shafts can be connected and an - # I-beam can be fixed at a certain height between each adjacent elevator shaft, with the same position as the ring beam. The pit must be equipped with an isolation net that is mm above the ground level.

Measure the beam edge distance between the upper and lower support beams. The measurement is to suspend the line from the upper support point to the ground for positioning, and then measure the horizontal distance from the positioning point to the edge of the lower support beam.Product range,Maintenance of elevator hall doors and car doors. Elevator malfunctions usually occur on the elevator hall and car doors, so attention should be paid to the maintenance of the hall and car doors. One is to refuel the fuel on the upper sill of the door and keep it in good condition, so that the elevator will not make unpleasant noises during operation and the opening of the door. Pay attention to the inspection of the safety contact plate or light curtain type contact plate switch wire of the elevator, as the frequency of opening and closing the door in the elevator is high, which can cause damage to the switch wire. This requires maintenance personnel to inspect it every time they work, and replace it in advance to avoid users having doubts about the quality of the elevator product due to door issues.The gantry elevator is used in the door legs of large gantry cranes to transport workers and maintenance components inside the gantry craneCleaning and cleaning of elevator car guide shoes. As is well known, the guide shoe runs on the guide rail, and there is an oil cup on the guide shoe. To ensure that the elevator does not make any noise during operation, it is necessary to regularly refuel the oil cup and clean the guide shoe and the cabin should be cleaned thoroughly.Kenneth, which is beneficial for reducing noiseThe requirement for the shaft is that it should not be plastered, in order to determine the configuration of certain shared devices, the order of shipment