category：Building materials / date：2024-04-16 06:17:15 / browse：43 / comment：6
Heating surface pipes, economizers, superheaters, reheaters, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, most of which is prestressed reinforcement. Where plastic deformation is not specified but compressive strength is specified,Grand caradusa40Cr precision alloy tube, such stainless steel plate can be applied.Grand caradusa,When the beam width is small, the reinforcement shall be bent.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.britain,Grand caradusa15CrMoG seamless pipe factory,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.C-section steel has uniform zinc layer, strong adhesion no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection. Small longitudinal crack
Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, high production efficiency, low cost and rapid development trend. The compressive strength of spiral welded pipe is generally higher than that of straight welded pipe. Narrow blank can be used to produce welded pipe with large pipe diameter, and blank with the same total width can also be used to produce welded pipe with different pipe diameter. However, compared with the straight seam pipe with the same length, the welding length is increased by ~ , and the production rate is low.H-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete which is convenient for settingHigh quality and low price,Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web so it is also named wide edge I-beam.GB No. I-beam is in height, in leg width and in waist thickness.Stages needing attention in the production and manufacture of alloy tubes
Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.Safety and health,I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Seamless pipe is made of steel block or solid pipe blank, and then made by hot rolling, cold rolling or cold dial. Seamless pipe plays an important role in China&#;s steel pipe industry. Seamless pipe production processes are relatively rich, generally according to the corresponding steps of processing and production. The defects can be removed by grinding with sand wheel but the remaining wall thickness must be within the allowable standard.Grand caradusa,I-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.C - section steel is reliable and stable in stress, can be accurately positioned,Grand caradusaThe software for turning reinforcement is, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibility
share 6 Comments
Comment / Cancel reply