AdministrationSPC flooring factoryEight common categories of / 20272article

category：Environmental protection / date：2024-04-09 02:10:44 / browse：41 / comment：5

floor leather is a layer of synthetic plastic decorative products. In addition to many advantages such as wear resistance, pollution resistance, corrosion resistance, moisture resistance, small water absorption, simple construction, it also adds the advantages of comfortable foot feeling, warm in winter and cool in summer of wood floor, narrowing the gap between wood floor and wood floor. No wonder floor leather will be so popular.If you are also worried about the shortcomings of wood flooring, good mechanical strength elasticity, good foot feeling strength, foot feeling wear resistance, corrosion resistance pollution resistance, heat insulation, sound insulation, moisture resistance, small water absorption, good insulation, self extinguishing, easy cleaning, simple construction convenient maintenance and low price. In a large number of civil buildings and public places, factories with high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor leather is m ~ m, the width is mm ~ mm, and the total thickness is mm (household) ~ mm (public building). days later, maggots grow on the floor. This problem occurs because the floor contains a lot of impurities.Administration,This is more suitable for deeper scratches. If the scratches are shallow, there will be no adhesion, and the actual repair will be discounted. It is suggested that partners can aggravate the scratches a little.Compared with WPC flooring, the price of SPC flooring is reasonable.However, you must choose one that suits your requirements.It&#;s better to spend more money on the floor you need, rather than low-cost floors.How to deal with furniture when replacing a new floor?In order to install a new floor, furniture and items must be removed.Professional laminate flooring must be installed in this process.The exact method you choose for furniture depends on several factors.You can start planning by asking yourself a few questions: how big is your new flooring project?Are you going to lay new floors in one room or the whole house?Hatvan,To sum up, the relief is really beautiful;If the same gram of wear-resistant paper is used, the wear-resistant degree of crystal is relatively higher than that of relief;The silent foot feel is really good, but it&#;s more expensive;Waterproof and cost-effective. Not many people know its role.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula,AdministrationEnvironmentally friendly wood flooring, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents,AdministrationComposition of laminate floor, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.The cross-section of the floor is rubbed with a file to generate heat in the cross-section, and you can smell the pungent smell at the same time). At this time, you can smell, generally you can smell three different levels of smell

From the surface of the floor, the solid wood floor can be polished and painted again even if the surface is damaged because it is the whole piece of wood.Tianhe floor adopts Jianfu paint, which is wear-resistant, scratch resistant, excellent surface performance, and greatly prolongs the service life of the floor.However, multilayer boards and laminates cannot do this. If there is a problem with the surface, the whole floor will be completely abandoned.If it is really serious or the actual recovery is not satisfactory, we must remove and replace the floor, find technicians to solve it, take out the seriously damaged wooden floor and remove it.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, and the tool shall be a toothed rubber scraper.During gluing, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting, and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.Equipment maintenance, Keep the floor dry and clean. If there is dirt on the floor surface, generally wipe it dry with a damp mop without dripping water.Floor leather (also known as coiled floor), a new type of flooring material,AdministrationWaterproof floor manufacturer, belongs to plastic products. It is one of the indispensable floor materials for modern room decoration. It has a thickness of more than mm and a wear-resistant layer of more than . Generally, glass wire with good flatness or double primer is used.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.Advantages of floor leather Various surface treatments (concave convex pattern, hand grasping pattern, mirror pattern).

Solid wood floor is very beneficial to physical and mental health, environmental protection and excellent home decoration effect.The price is quite expensive. Installation and maintenance must be done carefully and waxing should be done according to time.The price of ordinary solid wood flooring ranges from yuan / m to yuan / m, and some expensive ones even dare to reach yuan / mHow many years can solid wood flooring be used?From the perspective of the general service life of the floor, whether it is solid wood floor, reinforced composite floor or multi-layer composite floor, if it is used at home, it can generally be used for - years depending on the use environment.Credit guarantee,High price performance price ratio: because of its unique structural connection, the regulations on wood are not too high, and raw materials can also be used flexibly, so the price is much lower than that of solid wood flooring. Easy to install.How to lay lacquer cloth?The construction procedures and methods are as follows: first, measure the structural size of the room accurately;Then cut the lacquer cloth according to the size.Note that the cutting width should be slightly larger than the required width to facilitate overlapping, so that the crimped part of the floor paint cloth can be fully extended and ready for the final paving.Special adhesive shall be used for paving the floor paint cloth.Before paving, the indoor ground shall be treated first.Administration,Structure: artificial surface material, artificial basic, wood slag plus strong glue, additives and additives.After the high-pressure suppression of the panel splicing machine, it gets rid of the defect of poor wood reliability.Laminate flooring has reached grade B and has higher flame retardant performance, which is safer than other kinds of wood flooringIf the new floor is to be sent to a room equipped with large equipment, it may need to be rewired before moving.Make sure to contact an electrician before installing the floor.If the equipment needs to be moved, there is no need to worry that the heavy machinery will scratch it before installing the old floor.Keep tarpaulin and tape.