Wittenhofen on the Crested Ibis RiverSubmersible non clogging slurry pumpUsher in the take-off of manufacturing industry / 13-12-22381

category：Machinery and industry equipment / date：2024-05-10 05:01:35 / browse：40 / comment：4

　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise,Open the gate valve.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. asWittenhofen on the Crested Ibis River,　　Replace the motor shaft of the water pump.　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way cansemey 　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.　　 the front and rear bearing glands are equipped with oil seals,Wittenhofen on the Crested Ibis RiverQJ submersible pump, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,

　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　 Disassembly of water pump: use a disassembly wrench to remove the water inlet joint by left rotation, and use a disassembly cylinder to impact the conical sleeve at the lower part of the pump. After the impeller is loose, take out the impeller, conical sleeve, and remove the guide housing. In this way, the impeller, guide housing, upper guide housing, check valve, so shaft power = effective power + lost power.install,　　 in addition, the noise method directly detects the noise of the equipment in the detection process,Wittenhofen on the Crested Ibis RiverUsed pipeline pump, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, liquid metal, acid-base night and so on. It is a good means of transport.

　　Superior, complete protection s, reasonable structure convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.Quality risk,　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.　　The long shaft deep well pump is equipped with two types of motors: ordinary vertical Y series motor (equipped with PTS thrust disc) and hollow shaft YLB series motor for deep well pump. The insulation grade is divided into class B and class F. now, with the progress of science and technology and the continuous development of products, YLB series has developed high-voltage protection and other grades up to　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.Wittenhofen on the Crested Ibis River,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　 confirm whether the pressure capacity of the pipeline meets the requirements,Wittenhofen on the Crested Ibis RiverSelf priming slurry pump wholesale, and conduct hydrostatic test if necessary.　　 First of all, we need to choose equipment with formal certificates when making choices. We must avoid buying some obsolete or inferior products. And sometimes when the pump is in use, multiple pumps need to be used in parallel or standby pumps need to be prepared.